BOB  BECK  KLEMENS PULSERS

Frequently Asked Questions

Speed Comparison of Various Pulsers

Beck DIY Pulser                                    1 pulse per 12.5 sec        300 p/h

Standard Pulser                                     1 pulse per 3.5 sec        1,028 p/h

Standard Pulser                                      1 pulse per 1 sec             3,600 p/h 

Super T Pulser                                        65 pulses per sec         234,400 p/h

Super P Pulser                                        92 pulses per sec          331,200 p/h

Klemens Ultra Pulsa (2017)         124 pulses per sec         446,400  p/h

Klemens Ultra Pulsa (2019)          148 pulses per sec         532,800 p/h 
  
Klemens Spectrum (2020)             180 pulses per sec         648,000 p/h


International Power Supply - what about overseas?
All of our Klemens Pulsers will suit the 110V AC power supply in USA & Canada and will have the correct electrical fitting plug. It does not require purchase of any additional items such as a step down transformer.

I have heard that electrical fields can be harmful. What makes your Magnetic Pulser different? 
Some electromagnetic fields may be harmful, such as high voltage transformers, power lines, mobile phone towers, smart meters, Wi-Fi etc. The list goes on. This is commonly referred to as dirty electricity. This throws your body’s natural energy balance out of whack. Magnetic Fields generated by a Magnetic Pulser are designed to work with the body’s natural energy field by stimulating and rejuvenating the body’s natural energy field.


Does that mean the Magnetic Pulser is run on this dirty electricity? 
This is one of the unique advantages our pulsers have. We install Dirty Electricity Filters into our devices. These Dirty Electricity Filters contain a unique blend of natural activated earth elements that creates a natural harmonious energy field. This will reduce the harmful frequencies produced by various devices from coming into the magnetic pulsers.  Value $40

Where are the Magnetic Pulsers manufactured?
The Super T Magnetic Pulser weighs in at a sizable 4.6 kg, while the Super P weighs 4.8kg and the Klemens Ultra Pulsa weighs  4.99 kg packaged. These machines are not toys; they were built to function and to last. They are manufactured in Bundaberg, Queensland, Australia by our family business.


What is the Quality of the Magnetic Pulsers?
​We want to build machines that last - machines that aren't going to break down easily. Especially considering the amount of power going through these devices, quality and safety are of utmost importance to us. We are not trying to save a couple of dollars on cheap, lightweight international components. Our units are made from heavy-duty components that were built to last. As a result, our machines are quite heavy. This is to ensure only the best quality components and workmanship go into the machines. 

What are the radiation absorbers that come with pulser paddle?
The new pulser heads come with a  Radiation Absorber.  These are built with natural activated materials that absorb and neutralize harmful electromagnetic fields. The  Radiation Absorber even works when the unit is not turned on. Just keeping the pulser head near where you sleep will be of benefit.  It works simply by tuning into the body’s bio-field to reduce the amount of harmful frequencies within the body. This is included at no additional cost. We also include a dirty electricity filter on the mains coming into our instrument case.  These Radiation Absorbers are valued at $40 each but are free when you purchase our super pulsers.  These Radiation Absorbers stop the high frequency signals sent down the power lines.

How can I tell which polarity I am pulsing? 
There are two easily distinguishable sides to the paddle, a larger and a smaller side. The larger side of the paddle is bio-north, while the smaller side is bio-south. Each paddle’s polarities are tested at three different stages during manufacture to ensure polarity settings are correct. 

How strong is your magnetic pulser? 
Our unit generates such enormous heat that we have to use much more thermal protection over the paddle. However, this causes complications when trying to get an accurate strength reading from the pulser. For example, the Sota pulser has a covering of 2mm on their paddle. No more is needed because that unit doesn’t generate a great deal of heat. The Klemens pulsers have 10-12mm of heat protection. This means that the surface of the paddle is 5 times further from the coil than the Sota paddle. As with any other magnet, the greatest force is right next to the magnet, but then drops off dramatically afterwards. With a difference of 10mm, this has a massive impact on the strength readings.  This is demonstrated very clearly when testing both the Sota pulser and the Klemens pulsers. When testing the same pulser with one reading done at 2mm and one reading done at 10mm, the 10mm measurement showed 6 times less power.

Flipping Coins Like Slow Speed Pulsers
The Klemens Pulsers can induce coin dancing and an older, slower unit can be seen performing coin dancing here: https://www.youtube.com/watch?v=iId97dN9bgo

Our unit does not work quite the same as the slow speed pulsers that can make a coin jump dramatically. While the slow speed unit has flipped a single coin, the Klemens pulsers have already pulsed multiple times. This means that there is a reaction time necessary for a magnetic field to induce current into the coin to make it flip.  The Klemens pulsers operational speed is too fast to allow the induced magnetic field to remain to remain on long enough to create the reaction that allows the coin to flip with sufficient force as demonstrated with the slow speed pulsers. 

To put this into perspective, the slower pulsers can pulse once every 3.5 seconds. In this same time our Super T Magnetic Pulser has pulsed approximately (227 times). The comparison is even greater with our Super P Magnetic Pulser (322 times) and our Klemens Ultra Pulsa 2019 model (518 times).    

An interesting thing to note is that at 300mm, the readings of both pulsers were the same. 

There is no scientific research or data to prove that coin flipping is superior to coin dancing, in fact testimonials from customers and from our own experience suggest that high-speed units are more effective than slower speed units.  In some cases, low speed units did not produce any noticeable, positive results.

As far as the Gauss measurement and comparison you measured both the Sota and the Klemens from the coil. It seems to me that both should be measured from the outside since that is where the user would place it when treatment is administered.

The magnetic field's effectiveness ranges up to 300 mm so the extra structural coating on our units that we need to cover our coils due to the additional stresses on our coils, become irrelevant. 
    
If we put 2mm over our coils, they would fall apart. I suspect our coils also weigh about 3 times heavier than the Sota. We have never had a coil burnout either which is not the case with the Sota units. I was informed this information by a ex Sota agent. 

My only aim in the production of our units is do they work better than the slow speed units and do they achieve quicker results. I have had sufficient feedback from many customers to satisfy me that our units do produce these criteria. If I wasn’t convinced, I would have been making slow speed pulses as they are much easier to sell and would have sold more of them.

Can Using the Klemens Pulsers Make Me Tired?
We are not permitted to give any medical advice as we are not medically qualified practitioners.  We can say that some people report feeling tired when they first begin using our devices but that later they are able to increase the duration of their PEMF sessions without the fatigue.   

Can Using the Klemens Pulsers Cause Any Negative  Effects?
We are not permitted to give any medical advice as we are not medically qualified practitioners.  We can only refer people to the medical studies that have been published in an attempt to determine the answer to that question of safety. We recommend everyone investigate the medical evidence before using any PEMF device.  

 There have been some very interesting medical studies published about the effect of PEMF on human stem cells and bone marrow.  The studies demonstrate that, depending on how the PEMF is applied and the conditions surrounding the use of the PEMF device, there can be both positive and negative effects from the use of PEMF.  
​
https://www.ncbi.nlm.nih.gov/pubmed/25319486
wound healing and PEMF

https://www.ncbi.nlm.nih.gov/pmc/articles/PMC4834823/ 
stem cells - positive and negative effects of PEMF

https://www.ncbi.nlm.nih.gov/pubmed/26042793 
bone marrow and PEMF

​

Question:
Does the Ultra Pulsa paddle overheat?
​
When the correct instructions are followed, the Ultra Pulsar paddle does not overheat but becomes comfortably warm to touch.  If the unit is operated at speeds of up to 7 on the dial, at ambient temperature where the air can freely circulate around it, the paddle stays comfortably warm.  However when operating at high speeds (8-10 on the dial), or in a hot climate and/or in a confined area (ie under blankets/sheets) for over 15 mins, the paddle will become overheated to the point where it can burn skin.  Because we wish to prevent any chance of accidental burning of the skin, we supply a protective heat sock to go over the paddle and this sock should be kept permanently on the paddle.  We do not recommend using the paddle without the protective heat sock.

Even though our paddles are very often subjected to being overheated by incorrect usage, they continue to operate very well and to last for many years.  This is because we build them from very high quality materials.  The Ultra Pulser paddles can handle the heat, but skin can't.

To be clear, if the unit is used at high speed for over 15 minutes in a confined space with poor ventilation (under blankets etc) or also when it is a very hot day (eg 30 degrees celsius), the paddle can certainly become overheated enough to burn unprotected skin.  If used where a fan can blow air directly over the paddle, it does not seem to overheat.  We supply a protective heat sock that should be always used over the paddle.

Question:
What kind of units do you make and what are their ranges?

Answer:
We sell 4 different PEMF machines that have different frequencies. 
We also sell the other Bob Beck machines separately or more economically in packages. ie the Klemens Colloidal Silver Generator and the Klemens Zapper. We also sell the Ozonator.

The frequency is the speed ie the pulses per second which ranges from 10 p/s to 75 p/s.

All our pulsers are PEMF devices and they are all based on the Bob Beck protocol and technology.  

The Klemens Super T frequency ranges from 10 p/s to 75 p/s.
The Klemens Super P frequency ranges from 10 p/s to 92 p/s.
The Klemens Ultra Pulsa frequency ranges from 10 p/s to 148/ps
The Klemens Spectrum frequency ranges from 3 p/s to 180 p/s.

Question
Why do you recommend using an aerator with the Klemens Colloidal Silver Generator?

Answer
Although the quality of the silver rods is a constant factor amongst the silver generator manufacturers, the silver generator units are not all of the same quality or type. They don't all use the same electronic processes.

The Klemens colloidal silver generator units most effectively produce very fine nano-particles of colloidal silver if used with an aerator. If you don't use the aerator, then the silver particles will form quite rapidly and the particle size will be much larger and the least effective when compared to the nano size particles produced with the aerator. If you wish to prevent the fast erosion of the silver rods, you can use the aerator. There are two reasons why we use the aerator.
1. The particle sizes stay small (nano particles)
2. The smaller the particle size, the more effective.

Using an aerator is the most effective way of keeping the silver colloidal particles size. The aerator stops the particle size getting larger between the rods. Without an aerator, the particle size increases. With an aerator the particles are kept in circulation and the number of particles between the rods are kept to a minimum.

Aerators can be purchased from any pet shop that sell aquarium products or from ebay.

​

Contact 
​Klemens Pulsers
Phone: 61  7  4157  9962
Mobile:  61  407 257  453  
31  Old  Cedars  Road
South  Bingera  Q  4670
email: klemensanton0@gmail.com